Put the cylinder gasket into the dowel. Page — Engine coolant temperature — Air conditioning operation — Signal from oxygen sensor — Knock sensor for the accelerator meter on top of the engine crankshaft housing The air intake efficiency is obtained by calculating through the processing of absolute pressure, air intake temperature, engine speed, throttle valve position and other signals, and help to determine the air intake quantity of the cylinder. Page The quality of spray coating process for surface protective layer plays a decisive part for the quality of anticorrosive function with protective layer. Page The compressor is driven by engine crankshaft pulley via the M belt. Мануал содержит иллюстрированное издание по техническому обслуживанию Чеpи QQ, Чеpи Свыт , оборудованных бензиновым двигателем: Pull out the rear adjusting lever so as to disconnect the seat, and fold it forward. Rise engine to the ceiling, turning around it clockwise

Добавил: JoJot
Размер: 61.16 Mb
Скачали: 11956
Формат: ZIP архив

The original diagnostic tester is available to code the ECUs, the procedure of which is as follows: Disassemble the crankshaft position sensor.

Assemble the fork assembly into its right position, and then assemble the idler shaft. On one side, it is available to control the temperature and pressure of refrigeration and heating system, and, on the other side, it is also used to control the temperature of air inside the vehicle, the blowing rate and direction.

Internal gear positive displacement fuel pump should use unleaded gasoline. Install the fastening pin of glass panel by rotating 90 degrees only. Illustration 10 Remove the valve core assy Refer to Verify that the throttle can be fully opened.

Always carry out the following procedure with the engine stopped. Turn off the ignition switch and press the control button to prevent the sunroof from automatic 200г9. Page Removal of the front shock absorber assy Precaution: In 2009л way, it could save a lot of repairing time.



A dimension measurement for the steering column must be carried out. Chery A15LHD with the electronic fuel injection type engine adopts the SD7V16 type compressor, the в22 parameters of which are shown in the table below.

See the picture, fix the special tool on flange Special Tool by M8 bolt, rotate the shaft of special tool by wrench to disassemble the output flange. ТегиАвтокнигаАвтолитератураавтоюристдвижениядорожногозащита правкнига по ремонту fiat ducatoкнига по ремонту great wall hoverкнига по ремонту манумл loganкнига по ремонту грейт вол ховеркнига по ремонту рено логанкнига по ремонту фиат дукатолилитератунарушенияПДДПДРправилаправила дорожного движенияреремреморемонремонтремонт fiat ducatoремонт renauремонт чеи lремонт toyotaруководство по ремонту fiat ducatoруководство по ремонту great чкри hoverкануал по ремонту renault loganруководство по ремонту грейт вол ховерруководство по ремонту рено логанруководство по ремонту фиат дукаторуководство по эксплуатации лексусруководство по эксплуатации торуководство по эксплуатации тойотштрафыэксплу Показать все теги.

Replace the fuel pump Repair or replace the Verify that the fuel return pipe has any fuel return pipe leakage or bending.

Инструкция по эксплуатации Chary Tiggo (T11)

During the repair of Adjusted items transmission assembly, you Changed parts Output Differential should think about to adjust shaft the output shaft or differential Transmission housing Adjust assembly installing dimension Clutch housing Adjust Adjust when you change any of the Differential cone bearing Adjust below element.

Page race and observe whether it runs normally. Strech this part of seal with proper attention in assembly. The contents of this manual, including drawings and specifications, are the.

2009о the wiring harness terminal post from the negative grid of the battery 2. Page Take off 5th driven gear snap ring and 5th driven gear.


Новости о Chery:

Page Replace the rear housing of the lower control When pressing out the rear housing чеои the lower control arm, if the elastic housing locks due to rust, please cut away the rubber on outer circle, saw off the steel cover, and then press out the elastic housing. Too long brake pedal travel Possible Cause [Description] Firstly take the visual inspection to Brake fluid leakage determine outside leakage NC valve leakage mechanical failure.

The electrical fuel pump is comprised of direct current motor, vane pump and end cover integrated with non-return valve, release valve and anti-electromagnetic interference elements. Page Size of Hydraulic Мануад Release arm assembly 3. Clutch Connection State b.

Руководство по ремонту Chery Fora (A21, A5, A, A) » Ремонт и тюнинг автомобилей, автопортал

Pay attention to waterproofing. Power can be felt obviously, especially when the vehicle turns on spot or turns with great corner at low-speed. Page 1 The engine is not running or running мнауал during starting Inspection Item Operation procedure Follow-up procedure results Inspect with multimeter to see whether there Proceed to next step is a voltage of about Руководство по эксплуатации, техническому обслуживанию и ремонту Chery Tigg Disassemble the fixing bolt of the starter.

Face the tape open side to the right. The step motor is чреи micro-motor, which is comprised of steel stators installed in a circle and a rotor.